Bowling ball roll

Moderator: CPhillips

Bowling ball roll

Postby drafter » Sat Dec 10, 2016 8:09 pm

Win 8.1, 32 bit, sketchy physics, SU Make 2016
Have bowling alley (dwg) with ramp to start bowling ball. Ball rolls about half way then peters out.
File attached. What factor must be changed to cause ball to keep rolling?
0

drafter 
 

Re: Bowling ball roll

Postby SketchyPhysicsNutt » Mon Dec 12, 2016 2:09 am

Hi drafter i had play with your model and to get the strike power u need

i added a servo with hammer strike lever (both can be hidden from view)

press (S key) for strike and tweak strength and acceleration for your needs


BowlingAlley2
https://file.town/download/iwjof9w8wlcpdse8tsibdo53h

Hope it helps
Tez
0

SketchyPhysicsNutt 
 

Re: Bowling ball roll

Postby drafter » Mon Dec 12, 2016 3:40 pm

SketchyPhysicsNutt wrote:Hi drafter i had play with your model and to get the strike power u need

i added a servo with hammer strike lever (both can be hidden from view)

press (S key) for strike and tweak strength and acceleration for your needs


BowlingAlley2
https://file.town/download/iwjof9w8wlcpdse8tsibdo53h

Hope it helps
Tez


Thank you much. Are there other keyboard shortcuts you can share?
0

drafter 
 

Re: Bowling ball roll

Postby SketchyPhysicsNutt » Tue Dec 13, 2016 11:00 am

all scripts below go in controller panel

motor joints
key('z')-key('x') .........left/right
(0.5-rightx) ........left/right arrow keys
(0.5-righty) ........up/down arrow keys

servo joints
one for your bowling alley model automatic strike at frame 300
[0,1][(frame/300)%2] ....set servo min to -0.00
(rightx) ........left/right arrow keys
key('z')-key('x') .........left/right....set servo min to -0.00
oscillator(300) .......left/right...automatic

on joypad sticks or W,A,S,D keys
(joyLX) .....left to right / leftstick
(joyLY) .....up/down / leftstick

(joyRY) .....left to right / rightstick
(joyRX) .....up/down / rightstick

make sure u plug in joypad before u startup sketchup
0

SketchyPhysicsNutt 
 

Re: Bowling ball roll

Postby drafter » Sun Jan 01, 2017 11:12 pm

drafter wrote:
SketchyPhysicsNutt wrote:Hi drafter i had play with your model and to get the strike power u need

i added a servo with hammer strike lever (both can be hidden from view)

press (S key) for strike and tweak strength and acceleration for your needs


BowlingAlley2
https://file.town/download/iwjof9w8wlcpdse8tsibdo53h

Hope it helps
Tez


Thank you much. Are there other keyboard shortcuts you can share?


When I open this "revised" dwg, Controllers are absent. I don't know why.
0

drafter 
 

Re: Bowling ball roll

Postby SketchyPhysicsNutt » Tue Jan 03, 2017 12:53 pm

Hi mate don't understand what u mean by "Controllers are absent"

this may help u out


Tez
0

SketchyPhysicsNutt 
 

Re: Bowling ball roll

Postby drafter » Tue Jan 03, 2017 7:22 pm

SketchyPhysicsNutt wrote:Hi mate don't understand what u mean by "Controllers are absent"

this may help u out


Tez


When I his "start", A blank panel, where you expect to find controllers for such things as servos, is "Blank".
0

drafter 
 

Re: Bowling ball roll

Postby drafter » Tue Jan 03, 2017 8:04 pm

drafter wrote:
SketchyPhysicsNutt wrote:Hi mate don't understand what u mean by "Controllers are absent"

this may help u out


Tez


When I his "start", A blank panel, where you expect to find controllers for such things as servos, is "Blank".


Hold the phone!!
Tried it again and it works fine.
What threw me off was the letter "S" is the keyboard short-cut for SCALE. So the icon for scale kept appearing. So I deleted the short-cut.............And ALL is well.
Thank you for your time.
0

drafter 
 

SketchUcation One-Liner Adverts

by Ad Machine » 5 minutes ago



Ad Machine 
Robot
 



 

Return to SketchyPhysics

Who is online

Users browsing this forum: No registered users and 2 guests

Visit our sponsors: